Probleme, Fragen und Diskussionen zur MagicQ Software (im allgemeinen), z.B. Syntax, Patching, Paletten, FX usw.
Bitte hier keine Hardware-Fragen!
By fregel
#985
Hallo

Ich habe ein Problem, zum einen bei manchen Softwareversionen funktioniert das Multiwindow nicht. Zum anderen, bei denen wo es funktioniert muss ich bei jedem Start von der Software meine Fenster neu ordnen und skalieren.

Gibt es eine Version wo funktioniert und die Fenster bleiben wie sie sind?

MFG
By fregel
#987
zuerst hatte ich die aktuelle also die 1.3.6.0 und jetzt habe ich die 1.3.1.8
Benutzeravatar
By kr
#988
Hallo,

Seit SW 1.3.2.0 brauchst du eigentlich das extra Multi Windows Programm nicht mehr.

Auszug aus den Software-Changes:

Multi Windows on MagicQ PC without starting another application
MagicQ PC now supports a new Multi Windows mode, which enables MagicQ PC to use multiple windows on one PC with multiple monitors without starting up the separate Multi Window application.

This mode is easier to use than the previous method and uses automatic
sizing of the Windows on the extra monitors.

To use this mode, first set the Multi Windows option in the Interface settings in the Setup Window to Multi Windows (same PC).

Then select View System, View Remote.
A list of the monitors attached to the PC will be show together with their position and size. Press the RELOAD MULTI W soft button to update the list. Enable all the monitors that you wish to use for Multi Windows. Note that the Monitor that is running the main MagicQ Window must always be enabled.

Now it is possible to move Windows from the Main Window onto the other monitors. Press
SHIFT + SIZE to move a Window between the different monitors. Alternatively use the EXT button (was the PREV button, just left of the SIZE button) – this button is being reassigned for this function.

Sizing of Windows on the other monitors occurs just like in the Main Window – you can select full windows, half windows and quarter windows. The entire space on the other monitors is used for MagicQ Windows. When a Window is moved to another monitor the size is kept the same – for example, if it was a quarter window on the Main MagicQ Window it will be a quarter window on the other Window.
You can change the size on the other windows, just like on the Main MagicQ Window using the SIZE button.

Note that the original Multi Window mode using the Multi Window application is still supported. This enables users to run MagicQ PC and Multi Windows are on the same PC, or on different PCs.

mfg
By lightchange
#1912
sr das ich diesen alten Thread raushol aber wollte nicht extra nen neuen Erstellen.

Bin gerade dabei mich einwenig in das Chamsys reinzudenken und bekomm es einfach nicht hin mit dem zweiten Monitor.

Die software erkennt mir beide monitore, die Auflösung passt auch. Aber des mit dem rüberschieben und shift+size kappier ich irgendwie nicht.
Kann mir das mal bitte jemand erläutern?
Ich versteh das so das ich shift+size drücke und dann ein fenster auf denn anderen monitor ziehen kann. aber irgendwie funtz des nicht.

gruß
Michi
By Moscher
#1913
Hi
Also ich hab die 1.3.6er software, und du musst auf jeden Fall diese Einstellungen genau so befolgen, wie es im Beitrag über deinem steht!

Es gibt auch einen Button "EXT", damit kann man die Fenster auch auf den externen Monitor schieben...

Klingt jetzt alles etwas konfus, aber probiers einfach mal aus. Fenster markieren was auf den externen Monitor soll, dann EXT drücken...
By Zottel
#1914
Hallo Lightchange,

um das Fenster auf den anderen Monitor zu bekommen muss es aktiv sein.
D.h. wenn du vorher CLEAR gedrückt hast einmal mit der Maus hineinklicken, dann Shift+ Size drücken, das Fenster wird dann automatisch auf dem anderen Bildschirm geöffnet. Es ist also nicht wie bei bspw. Windows XP das du ein Fenster hin und her schiebst.

Hoffe ich konnte helfen, bis denne

Gruss Zottel
By lightchange
#1915
So Problem gelöst

der Fehler war mal wieder einfacher als gedacht.
Hatte Multiwindow nicht aktiviert gehabt in der Software.

Hab diesen Text
To use this mode, first set the Multi Windows option in the Interface settings in the Setup Window to Multi Windows (same PC).
falsch verstanden, dachte die meinen die XP Einstellungen.

Funktioniert allso jetzt wunderbar.
Aber danke für eure schnellen Antworten.
Kommen bestimmt noch mehr :-)


Gruß
Michi